RELATED SUZUKI OUTBOARD SEARCHES:
PROPELLERS
Overall, the Suzuki Outboard Manual is a highly reliable document written by industry experts with helpful tips such as break-in information for your outboard motor to ensure maximum performance. And the best part is that this manual is available for different models so you can cater to your specific Outboard’s problems. Jan 18, 2013 Trust Suzuki Outboard DT50DT60 DT65 DT55 DT65 DT75 DT85 Service Repair Manual will giveyou everything you need to do the job. Save time and money by doingit yourself, with the confidence only a Suzuki Outboard DT50 DT60DT65 DT55 DT65 DT75 DT85 Service Repair Manual can provide.Models Covers:Suzuki DT50, DT60, DT65 prior to 1985Suzuki DT55, DT65.
M = Manual Start, Tiller Control N = High thrust or sail model available in 8 and 9.9 hp QH = Tiller Control with gas assisted tilt (some DF25/30/40/50) R = Remote Control, Electric start S = High performance 150 HP with EFI (designed for bass boats) SF = Super Four.
An outboard motor is designed to develop its rated power within a specified engine speed range. The maximum rated power delivered by the Suzuki models are shown in your service manual. If the standard propeller fails to meet the above requirement, use another pitch propeller to hold the engine speed within the range specified in your manual propeller selection chart.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Installing a propeller with pitch either too high or too low will cause incorrect maximum engine speed, which may result in severe damage to the motor.
Disassembly of propeller shaft components
1. Slide propeller shaft away from reverse gear housing assembly
Account for reverse gear back-up shim thrust washer
Jun 30, 2013 X3 is a time consuming game. Stock exchange is no different. Unless you get a satellite in Kingdom's End, you will have to sit around to access the stock exchange. During that time you won't really do anything because you need to actively Time accelerate with SETA. Oct 14, 2015 X3: Albion Prelude. All Discussions Screenshots Artwork Broadcasts Videos News Guides Reviews X3: Albion Prelude General Discussions Topic Details. Oct 14, 2015 @ 8:04am stupid stock exchange won't unlock! Stupid stock exchange won't unlock! Argon Stock Exchange / Stock Exchange Argon Stock Exchange / Stock Exchange / X3 Albion Prelude: X3AP: X3 Albion Prelude: X3 Albion Prelude. X Games Forum; Knowledge base; Ships properties; X3 Albion Prelude map; Ware search; Stations search; Asteroid. X3 albion prelude stock exchange.
2. Remove horizontal slider and forward gear thrust washer
3. Remove spring
4. Using special tool, push dog pin shifter.
5. Kaspersky endpoint security 10 databases are corrupted. Remove clutch dog shifter propeller shaft.
PROPELLER
• Inspect propeller for bent, chipped or broken blades and replace or repair if necessary.
• Inspect propeller bushing splines for wear or other damage and replace if necessary.
• Inspect propeller bushing for deterioration or slipping and replace if necessary.
PROPELLER SHAFT COMPONENTS
• Inspect horizontal slider and connector pin for excessive wear or other damage. Replace if necessary.
• Inspect clutch dog shifter for excessive wear, chip or other damage. Replace if necessary.
• Inspect dog pin for bent or other damage. Replace if necessary. Socom fireteam bravo 2 save file.
• Inspect propeller shaft / splines for wear, twist or other damage. Replace if necessary.
PROPELLER SHAFT BEARING HOUSING
• Inspect housing for cracks or other damage. Replace if necessary.
• Inspect propeller shaft bearings and reverse gear bearing for pitting, rough or other damage. Replace if necessary.
• Inspect oil seals and O-ring for cuts, nicks or tears.
Replacing propeller shaft oil seal
1. Remove retaining ring
2. Extract oil seals
1 and washer 2.3 using oil seal remover.
Do not re-use oil seal once removed.
Always use a new oil seal.
3. Apply Water Resistant Grease to inner circumference of housing.
4. Using an oil seal installer, drive two oil seals (one at a time) into housing.
The lipped portion of seal should face towards propeller.
Apply Water Resistant Grease to seal lips.
5. Install washer and retaining ring.
PROPELLER INSTALLATION
1. Install spacer shaft, then slide on propeller
2. Fit spacer specified torque.
Suzuki Outboard Troubleshooting Guide
1 and propeller stopper 2 onto propeller3.4, washer 5 and nut 6, then tighten nut to
![Suzuki Outboard Dt85 Manual Suzuki Outboard Dt85 Manual](https://i.ytimg.com/vi/kCyFDsP8DC4/hqdefault.jpg)
Propeller nut : 55 N.m (5.5 kg-m, 40.0 lb.-ft.)
3. Push cotter pin secure.
Suzuki Outboard Dt85 Manual 2017
PROPELLER SELECTION FOR COUNTER
ROTATION
For counter-rotation model, newly designed stainless steel propellers are available as follows.
Suzuki highly recommend to use the genuine Suzuki counterrotation propeller for the counter rotation model. In case of twin installation, always use on both engines, the same size normal rotation and counter-rotation propellers.
ENGINE CRANKED, BUT NOT START (OR STOPS SHORTLY AFTER STARTING)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)
UNSTABLE IDLING / TROLLING (OR ENGINE TENDS TO STALL)
• Incorrect by-pass air screw adjustment [NOTE3]
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)
• IAC valve failure [NOTE3]
• IAC passage failure (clogged hose, etc.) [NOTE3]
• Spark plug failure
• Ignition coil failure
• ECM failure
• Wire continuity / connection failure
• Failure of high pressure fuel system components :
• Fuel injector (clog, stuck valve, etc.)
• Fuel pressure regulator (incorrect regulated pressure, etc.)
• Fuel pump (clogged suction filter, leakage in tank, etc.)
• Fuel filter (clog, etc.)
• Hose (clog, kink, leakage, etc.)